Walksnail Avatar GT2 Digital FPV Kit | VTX & Pro Camera
- Free US shipping on orders $100+
- In stock, ready to ship
- Backordered, shipping soon
PayPal — Same-Day Processing
Fastest shipping with same-day processing & Buyer Protection. All credit cards accepted at checkout through Shop Pay (installments available).
Pay Over Time with Affirm & Shop Pay Installments
As low as $49.91/mo with Affirm, or choose Shop Pay Installments at checkout — Prequalify now, no hidden fees
Save 10% at Checkout
Use code SAVE10 for 10% off your order
- Secure Checkout
- 30-Day Defect/Damage Returns
- Fast & Reliable Shipping
Digital FPV Video for Your Next Build
The Walksnail Avatar GT2 kit pairs an Avatar GT2 video transmitter with an Avatar Pro camera for a compatible digital FPV installation. Listed 1080p and 720p modes, Canvas-mode OSD support and a microSD slot give you a foundation for an aircraft-side video system without including a complete aircraft or headset.
Plan the VTX mounting, camera position and cable route together before assembly. With two listed VTX mounting patterns and a 140mm camera coaxial cable, you can check fitment against your frame before powering the system.
Key Features
- Avatar Pro camera: Listed 1/1.8-inch Sony STARVIS II sensor in a 19mm-wide camera housing.
- Digital video modes: Listed 1080p/720p image resolutions; available frame rates and modes depend on the compatible receiving equipment and firmware.
- Canvas OSD: For supported flight-controller integrations with correct wiring and configuration.
- microSD support: Listed capacity support up to 256GB. A memory card is not confirmed as included.
- Two mounting patterns: Listed 20 × 20mm and 25.5 × 25.5mm.
- Power input: Listed 11.1–25.2V; confirm the actual supply stays within this range throughout operation.
Technical Specifications
- Model: Walksnail Avatar GT2.
- Camera: Avatar Pro.
- Camera sensor: Listed 1/1.8-inch Sony STARVIS II.
- Communication frequency: Listed 5.725–5.850GHz.
- Channels: Four listed.
- Input voltage: 11.1–25.2V.
- Image resolution: Listed 1080p/720p.
- Minimum latency: Listed 22ms under applicable test conditions, not a guaranteed end-to-end delay in every mode.
- OSD: Canvas mode.
- Interfaces: JST 1.0mm 6-pin power connection, microSD card slot and USB Type-C.
- VTX dimensions: 34 × 36 × 23.5mm.
- Camera dimensions: 19 × 19 × 24mm.
- VTX mounting: 20 × 20mm or 25.5 × 25.5mm.
- Listed kit weight: 52g excluding antenna weight.
- Antenna connector: MMCX.
- Listed antenna polarization: LHCP; confirm supplied antenna contents separately.
- Camera coaxial cable: Listed 140mm.
- Operating temperature: Listed −10 to 40°C.
Compatibility and Setup
Confirm that your goggles or receiver specifically support the Walksnail Avatar system and the GT2's required firmware. Sharing the 5.8GHz band does not establish compatibility with analog, DJI or HDZero video equipment.
The source lists flight-controller integration with Betaflight, INAV, Fettec, KISS and ArduPilot. Available OSD functions and control features depend on the exact controller, firmware and wiring; this is not a promise of plug-and-play support with every board running those platforms.
Check the 6-pin connector pinout, supply current requirements, camera clearance and cooling provision before installation. Do not connect directly to an 8S battery: the listed maximum input is 25.2V. Battery cell count alone is not enough to verify the complete operating-voltage range.
Perfect For
Experienced FPV builders adding an aircraft-side digital video kit to a compatible Walksnail Avatar receiving setup, with verified frame space and power requirements.
Package and Option Details
The selectable option is Avatar GT2 Kit / No plug. This listing identifies an Avatar GT2 VTX and Avatar Pro camera kit, with a listed 140mm coaxial cable. A complete accessory and quantity list is not provided, so confirm antennas, power harnesses, mounting hardware and any additional cables before ordering.
The “No plug” label does not establish which power leads or connectors are supplied. Goggles, a video receiver, memory card, battery and aircraft are not confirmed as included.
Installation and Safety
- Remove propellers before bench setup.
- Disconnect power before wiring or handling connectors.
- Confirm voltage, polarity and every pin assignment before powering the VTX.
- Connect the correct antenna before transmitting and provide the required airflow.
- Avoid prolonged powered bench operation without suitable cooling.
- Configure channels and transmitter power for your operating location using the manufacturer's instructions.
For package or integration questions, contact sales@buyrcdroneoutlet.com.
Shipping Policy
Estimated Delivery: Orders ship within 24–48 hours with full end-to-end tracking. Transit times typically take under 13 days (6–12 business days) to most destinations.
International Shipping: Global fulfillment from our nearest warehouse with tracking provided upon dispatch.
Return & Guarantee Policy
Return Policy: Defective or damaged item? Return it within 30 days for a full refund. Customer pays return shipping.
Technical Support: Need help with compatibility or setup? Contact our US-based FPV experts at (951) 592-5658 for free assistance.
